gruvlok fitting fittings florida

Style 38 Coupling - Also available are STAB 38 Couplings supplied with armored or armored/pinned gaskets in 2″ thru 12″ sizes.

Style 401 SEAL-PLUS Compression Coupling - SEAL-PLUS restraining end meets or exceeds all requirements of the applicable D.O.T. codes for performance and safety.

Style 501 SEAL-PLUS Compression Couplings and Fittings - Like the “401” coupling, the “501” can be disassembled, re-assembled, and the joint re-made, if necessary.

Style 90 Universal Coupling - Properly assembled plastic pipe joints made with the Dresser “Universal” Style 90 product line meet or exceed the requirements of D.O.T. 192.283(b).

Style 90 Insulated Restraining Coupling - The Style 90 Insulated Restraining coupling is available in 3/4″, 1″, 1-1/4″, 1-1/2″ and 2″ nominal IPS sizes. (Dresser furnishes insert stiffeners for PE pipe in all SDR sizes commonly used in polyethylene piping systems.)

Style 501 Service Tee - Like the “401” coupling, the “501” can be disassembled, re-assembled, and the joint re-made, if necessary.

Style 64 Bolted Riser Tee - Style 64 Bolted Riser Tees are available in 3″ and 4″ I.D. for both steel and P.E. pipe sizes. 64 Riser Tees are supplied with the Style 711 insulating inlet and conductive outlet design.

Style 700 Boltless Hydraulic Coupling - Universal POSI-HOLD couplings, ells and tees are available in 3″, 4″, 6″, 8″‚ sizes, and conforms to all performance requirements for P.E. pipe joints outlined in D.O.T. 192.283b.

Style 711 Coupling - The Style 711 coupling is available from 1-1/4″ through 12″ sizes and exceeds the requirements of D.O.T. Code 192.283(b) provided the proper Dresser reinforcing insert stiffener is used in the P.E. pipe end.

Style 731 Restraining Line Cap - AL-CLAD epoxy coating is available for corrosion protection far superior to that of field applied coatings. Anode connectors are also available upon request.

Style 88 Coupling - Style 88's are available in couplings, ells, and male and female adapters from 1/4″ through 1-1/4″.

Style 88 Adapter - Available in male adapter sizes for steel x CTS from 1″ - 2″ sizes.

Style 90 Coupling - Dresser Style 90 Fittings have been installed for steel x steel natural gas service line connections where they have helped to speed installation and cut costs.

Style 90 Universal Tap-n-Valve Tee - Retains the slug after tapping the main.

Style 91 Service Saddle - Dresser Style 91 saddles are furnished with 1/2″ thru 2″ NPT tapped bodies. They are available in single and double stirrup configurations and each is designed to accurately fit the pipe within a range of each nominal size - clearly marked on each saddle body.

Style 39 Couplings - Style 39 couplings can be virtually used on all sizes of gas and oil pipelines, and can be supplied with insulating features on both ends if required.

Style 40 Long Couplings - Larger sizes are available and special length bodies can be supplied.

Style 39-40 Insulated Long Couplings - Available in steel pipe sizes 1″ thru 16″.

Style 39-62 Insulated Reducing Couplings - Type 1 Style 39-62 is available in standard sizes up to 24″ I.D.; and Type 3 Style 39-62 features a long-sleeve body in nominal sizes 4″ thru 24″.

Style 31 Line Cap - The Dresser Style 31 Line Cap is regularly supplied with a 1" NPT vent and plug off-center and is also available as a pipe-end separator.

Style 128 Flange Adapter - ANSI B16.5 Class 150 flanges supplied as standard. Larger sizes are available upon request.

Style 63 Expansion Joint - Special packing and lubrication requirements are custom-matched to specific fluid processes or application requirements. Pressure ratings available up to 1200 psi.

Style 175 GTO Gas Service Valve - A plastic ring inserted between the retaining ring and bonnet, plus permanently lubricated port seals, assure low, uniform operating torque, preventing the plug from freezing to the body.

Style 175 Gas Service Valve - Compression-end 175 valves employ the Universal 90 locking design to create a positive pipe restraint on both ends.

Style 175 X 90 Gas Service Valve - The Style 175 valve is assembled at the factory and sealed against tampering by a spring loaded stainless steel retaining ring, which cannot be removed with ordinary tools. It is tamper proof as specified in D.O.T. 192.363 Part C.

Style 175 Cut In Gas Service Valve - Available with FIPS x Compression and Compression x Compression Universal ends, the “Cut-In” 175 valve is thoroughly tested at high and low pressure prior to shipment.

Style 275 Meter Valve - A 3/4″ x 1-1/4″ size in all type configurations is also available.

Style 350 Ultra-Seal Meter Valve - Available in 1-1/4″, 1-1/2″ and 2″ valve sizes with operating pressures from inches of water column to 175 psig.

Style 351 Meter Set Strainer - Dresser recommends the inclusion of gasket strainers in its prefabricated systems to protect pipeline valves and regulation equipment.

Style 575 Angle Ball Valve - The “575” is available in inlet sizes 1-1/4″ or 1-1/2″ MIPT and an outlet size of 1-1/8″ OD, but it can be readily adapted to other outlet sizes as required.

Style 2275 Gas Stop Valve Changer - The Style 2275 product line is available in sizes 5/8″, 3/4″, 1″, 1-1/4″ and 2”. The 2” size is provided with a safety clamp.

Style 480 Excess Flow Valves - Dresser EFV’s can be supplied in a variety of fusion, weld, and mechanical configurations.

Style 4 and 41 Collar Clamps - Dresser Style 4 and Style 41 collar clamps stops all leaks through screw collars.

Style 77 Band Clamp - Cone gaskets must be specified when ordering the Style 77B repair clamp; 1-5/8″, 2″ and 2-1/2″ size cone gaskets available. Band and lugs are made of carbon stel to AISI C1008/1010.

Style 60 and 160 Bell Joint Clamps - Made of cast dultile iron to ASTM A536; spigot rings to ASTM A-307.

Style 118 Repair Clamp - The Handiband clamp is made of stainless steel for corrosion resistance. Dresser Grade 304 rubber gasket offers resistance to oil, condensates, natural gas and gasoline.

Style 360 Repair Clamp - The “360” has a stainless band, lugs of rugged ductile iron and bolts of corrosion-resistant Dresserloy.

Style 440 Joint Harness - Today's joint restraint problems are becoming more complex. Whether steel, cast or ductile iron, the STAR National Products joint anchor restraint system offers a wide range of flexibility and adaptability, and can be customized to meet most field construction requirements.

Style 80 Repair Sleeve - Style 80 sleeves are available from 2″ thru 8″ CIP sizes and recommended for all customary pressures where pipe wall thickness is in conformity with specifications for standard cast iron pipe.

Style 126 Repair Sleeve - Side bolts, which are fully enclosed within the sleeve body to prevent corrosion, are tightened to compress side gaskets providing a complete, permanent leakproof seal.

Style 50 Repair Sleeve - Available with or without branch outlet from 6″ thru 24″ nominal CIP sizes.

Style 50A Hot Tap Sleeve - CIP pipe sizes from 6″ thru 24″ with 100 PSI MAOP.

Style 54 and 73 Repair Sleeves - Style 54 and 73 Cast Split Sleeves are designed to completely enclose and repair defective screw collars, plain or butt bell and spigot joints and double-bell circumferential welded joints.

Style 93 Repair Sleeve - Cap screw design provides added circumferential sealing capability around the pipe.

Style 96 Repair Sleeve - Sleeves are also vented for installation under pressure.

Style 97 Repair Sleeve - All clamps feature a 1/2″ NPT relief plug.

Style 110 and 115 Weld Repair Sleeves - Built to rigid Dresser specifications, Style 110 sleeves have a minimum yield strength of 50,000 psi and an ultimate strength of 70,000 psi.

Style 220 Weld Repair Sleeve - Larger diameters and longer sleeve lengths may be fabricated to customer specifications.

Style 220S Weldover Sleeve - Dresser Style 220S Sleeves are rated to 350 psi working pressure and meet D.O.T.#192 code requirements.

Pressure Balanced Repair Sleeve - For use on gas and liquid transmission pipelines with general loss corrosion, coating failure anomalies or third party damage

Dresser Style 850 Insulating Sleeve - A stabilizing rib in the sleeve body accurately centers the 850 on the main and prevents any excessive end-pitch of the pipe after the cutting operation.A stabilizing rib in the sleeve body accurately centers the 850 on the main and prevents any excessive end-pitch of the pipe after the cutting operation.

Phone (863) 425-0023 Fax (863) 425-5091